Why use Natural stones?
Sharpening particles of natural stones are uneven in their sizes and the resulting edge's "teeth" will also be uneven, making a knife stay sharper for a longer time as the "teeth' will dull unevenly
Natural stones dish at a much slower rate then synthetic, so a natural stone will last longer then a synthetic one and doesn't need to be flattened often. A good size natural stone will last a life-time
Natural stones remove burr easier than synthetic stones, hence a knife gets much sharper and holds sharpness for much longer
Natural stones will create a hazy kasumi finish
I work as chef and use my knifes a lot and I can feel a difference in performance when a knife is sharpened on natural or synthetic stones.How To Select Stones
In general, softer natural stones are more useful for kitchen knives and are easier to use than harder stones, so it is best to start with softer stones and get harder stones as your skills improve. Some very hard and fine stone can scratch soft iron (jigane) but not hard steel (hagane), that is not because stone is bad but cause steel is softer then stone it self. So you have to use them with care and use these stones only with slurry and light pressure. This hard and fine stone usually the most rare and expensive stones. These stones are very good for tools and razors.
I will not talk much here about stones from rare mines and stratas, as I think most important is to get a stone that works best on your knife or razor, and it might not matter as much which mine and strata it comes from.
However, for clarification purpose, all stones on the website will include a name of the mine (i.e. Ohira), a strata the stone was mined from (i.e. Tomae), an appearance (i.e. Asagi), and a hardness level (Lv 3). A cutting ability of a stone will also be noted.
1. Mine (Nakayama, Ohira, Hakka, etc.)
2. Strata (Tenjyou, Namito, Tomae, etc.)
3. Appearance (Kiita, Karasu, Asagi, etc.)
4. Stone Level (Lv1 - Lv 5, Lv 5 - hardest)
So example will be:
Ohira Tomae Lv 2, Nakayama Asagi Lv 5, Shinden Suita Renge Lv 3.5Stratas
From soft on top and very hard on the button.Natural stones Quarries
Nartuaki - 鳴滝 (also has 2 meaning: mine name and east mines)
Shiroto: connected to Oozuku
I have been dealing in Japanese natural sharpening stones for some time now, and through my experiences with both wholesalers and customers I have realized that there are quite a few misunderstandings about these fabulous antiquities.I think many have a tendency to look at Japanese polishing stones from only one perspective instead of seeing every stone as entirely unique; each with its own multifaceted set of qualities. I have seen the claim on numerous occasions that only “old” or “rare” stones are worth buying because only they possess the best sharpening qualities. This false claim is usually conjoined with the idea that “new stock” stones are of a lower overall quality than previously sold stones.To clarify, the geological time scale does not work on the same time frame that we consider “old and young”. To add some perspective, all Japanese natural sharpening stones were formed during a period of about 500 million years, so it seems unlikely that there is a huge difference between a stone mined 100 years ago and one mined 60 years ago. In fact, most mines were closed 60-70 years ago, and the current stock of stones bearing their kanji comes from raw material excavated before the mine closure and stored for later use. So in reality, not much quality difference exists between stones stamped 60 years ago or stamped today, only the methods in which they are cut and flattened. The only quarry still being actively excavated is the Marouyama mine but also very rarely Ohira. This is important as some vendors are spreading misinformation that older stones are of higher quality in order to fetch higher prices for their stock. With the above in mind, I would like to share some information in hopes of explaining how the stone business in Japan operates. All sales in Japan are now done by a few wholesalers: Tanaka, Imanishi, HaTanaka, Asano and ,a few others. All current wholesalers have huge amounts of old stock raw material: Ohira, Ozuku, Nakayama, Shobudani, Okudo etc. This is not to say that stones from any two wholesalers will be the same, far from it. All “in stock” stones at every wholesaler will have a variety of qualities that make them unique, such as varying strata, hardness, fineness, and color combinations (red, yellow, gray, green and etc). But these unique attributes do not depend on when they were chiseled as raw material from the mine, but instead depend more so on the person who selected the original raw material, and current market demand for certain stones. Demand for certain types of stones (ie. Kiita or Light Suita) dictates which of the raw material will be processed first. In Japan, the highest demand for stones comes from local carpenters and sword polishers, not from knife or razor users. In fact, the number of people in Japan that buy and use natural stones for razors and knives is less than 1% of the total market share. Razor quality stones are very hard and fine, and often not useable for knives or tools because they scratch the soft steel cladding and are very slow. These types of stones are of little use to busy carpenters or chefs (i.e. 99% of the market share), whose tools need to be maintained with as little work as possible. Because of this, very hard and fine stones are not highly sought after, and due to their low overall demand in comparison are actually considered less valuable. This, however, does not mean that they are bad, far from it. Iwasaki San and other razor smiths have personally conveyed their preference for very hard Nakayama or Ozuku.A recent tendency among carpenters is to use super hard Asagis for Ura side of their tools.In the past carpenters were way too busy and they had to sharpen their tools on building sight so they needed super fast stones that could bring back their tools sharpness within minutes and they did not want to carry 5 or 6 stones, that would have been way too heavy and cumbersome. So they needed stones fast and fine at the same time. Thats why they preferred Suitas for tools, not finest Suitas just middle fineness and they did not care much about inclusions or lines and those stones are now very hard to get as they are all bought up. One can get much better result with Very fine Nakayama or super hard Ozuku but it just takes more time.For sword polishing the most sought after stones are Asano Koma Nagura and Uchigomori stones.Uchigomori come only from Ohira and Mizukihara mine, those stones are only between 3000 and 5000 grit, not more. They are known for their super soft particles that will not scratch Tamahagane steel. They are not as fine as some think, Tamahagane is quite soft steel and it can not handle to fine polish, it will also get scratched when harder stones are used. Uchigumori are also very slow stones, they are not used for sharpening, as many think, they are only used for polishing and to bring contrast between hardened steel clouds and the hamon.Asano Naguras are mostly used by carpenters and sword polishers, and thats is why there is so little supply of them right now. Koma is especially scarce because it is fastest but also very fine. Another factor for high price of Koma nagura is that Koma supply of raw rock that yields quality stones is almost depleted. There are many sellers that sell naguras that are not Asano certified and of inconsistent quality. Only Asano stamped naguras are certified for quality and authenticity.A few words about the different wholesalers.There are many stone wholesalers in Kyoto and even outside Kyoto that bought these huge piles of raw stone material. They have different criteria of stone evaluation and processing That is why you see sometimes huge price difference between stones of similar quality.
The price of stones is also determined by demand. Stones that are more sought after(kiita, light Suitas) are more expensive than stones that are not in high demand (darker stones, asagi)
The color of the stone is not the only determining factor of the sale prices, for instance if many sellers start to ask a lot for a Ozuku asagi then Ozuku asagi price will increase a lot from that wholeseller, in general Nakayama are most sought after stones in Japan. Because of the high demand price for those stones have gone up considerably in the past year. Right now Nakayama Kiita and Suita stones are selling for extremely high prices, this also leads to a lot of stones from other origin being sold as Nakayama. We are aware of some vendors in US that are seling Ohira stones misrepresented for Nakayama, asking premium prices based on name recognition alone. Some sellers will claim that they can tell the stones mine of origin by its skin or its looks, this is plain rubbish so be aware. I have asked numerous stone experts in Japan if its even possible and all of them agreed that its very hard to tell stones origins from the skin. There are very very few experts in Japan that can guess what stone is what and that is only done by testing the particular stone.
Why are harder stones for experienced users only?
The harder the stone the harder it is to raise slurry from it, on Japanese Natural stones slurry does the work and polishing so if you do not get slurry from your stone there will be no result at all to the user. At same time super hard stones are also some of the finest and best for razors. In order to get the maximum out of a very hard razor stone, one has to have some experience with how Jnats work, to understand the slurry break down, and polishing characteristics. In order for that to happen one should start with a bit softer stone and when one learns how to use the stone properly one can move to a truly hard razor quality stone and experience the finest edges there are.
If you travel around Japan and see some vintage Kamisori stones you will find a lot of those Super hard Gray Stones (Asagi) from Nakayama, Shoubudani or Ozuku
There is some that have used Nakayama Kiita but price for those was a lot higher.
When Iwasaki san did experiment between bright Yellow stones and Gray, Green he found out that in result there was no difference at all, only the price
Kiita stones are of course considered better because one can easily see swarf and progression of the sharpening process. These stones are almost gone now and super expensive. One can find many soft kiita stones but they are too soft and not useful for razors.
Hard stones being bad for honing is an inaccurate statement. A person that claims that has very little experience and knowledge with Japanese polishing stones or only has looked at them from one point of view, tools, knives etc.
Thats why it is very important to test all stones on a variety of cutting tools, something we do with every stone we sell.
The biggest problem I see for new users of hard Japanese stones is that they do not do enough pre polishing first. Many claim that their hard stones are not finer than their medium hard stones. But fact is that very hard Jnats are extremely fine and with the first passes will reveal scratches from the previous coarser stones. They tend to leave mirror finish to the blade if not used with slurry and that mirror finish reflects all the scratches that were left from other stones. When using a hard finishing stone in such a manner a person can be mislead to think the stone is not fine, while in fact the person did not spend enough time on the stone.
Best use for Finishing Stones:
Soft Stones: Beginners, tools, Kitchen Knives, Other knives
Medium stones: Tool finishing, High End Kitchen knives, Razor Beginner
Hard Stones: Razors ,For Ura Only on high end tools
Thats it for now :) More to come